It’s just an Exhaust……..

One weekend we decided to take the plunge and begin the process of replacing the exhaust from end to end. We had purchased the exhaust a while earlier and now it was time to take the hole ridden rot box off the stag and put the shiny new exhaust on.

The New Shiny Exhaust

The New Shiny Exhaust

With the exhausts approved by the dogs we loaded the stag on to the car lift and began what would turn out to be a long a drawn out process.

Once the stag was on the lift we could get a full look at the state of the exhaust and it was not pretty, between holes, rust and brackets falling off it made it an interesting adventure.

Have now seen the state of our exhaust we started by getting the nuts off the manifold end of the exhaust, well, we tried, 5 out of 6 nuts said yes but there is always the one that says no, and boy did it say No with a capital N.

A Stuck Bolt

A stuck bolt

These will get it out

These will get it out

When i said it said no, i mean it would not budge when we asked it nicely, hit it, used a socket set, bought and used nut extractors and finally swore at it – this thing was not for moving. We spent several hours using a junior hacksaw cutting round the bolt in the exhaust to see if we could get more purchase one the delightful little treasure.  After many hours of trying to get the bolt out we put in a call to friend with a welder who reckoned that we could possibly weld a nut on to the bolt and this would allow us to get some more purchase on the nut.

So, one cold january saturday morning our friend appears with his welder in the boot and Jules was wandering around like a kid in the sweetie shop wanting to have a go with the welder. So up went the stag yet again, welder was plugged in and 2 little goblins were sat under the car full of intent and optimism. At this point the the welding started and slowly over the coming hour the the colour of the air began to turn blue as the nut would weld to the bolt, but the bolt was not for budging.

After a couple of hours of trying to weld something, anything to the bolt to get it out we had to admit defeat and discuss the options, of which there were only 2, our friend goes home and gets their plasma cutter and we cut it out or we drill it out – out came the drill!

After a spot of lunch the rest of the afternoon are dedicated to drilling out the infernal bolt, and when i say the rest of the afternoon, it was light when we started and dark when we and finally drilled the little treasure out – now we can begin the the process of putting the new exhaust in place, well we can on sunday.

Up bright and early on the sunday morning to begin by removing the remaining parts of the exhaust left on the car from saturday and started the process of putting the new exhaust on to the stag, but first we had to find a bolt that would work with the new hole drilled out on saturday, and with this new bolt in place we begin the tricky job of getting all the parts lined up.

First to go on are the brackets to support the exhaust just before they go thru the cross member, and then the great threading began starting at the manifold end and then gently bolting up the each part loosely to allow us flexibility to nudge the exhaust in to place.

It took a couple of hours to get in to place where we could start to tightening everything and look to put the new oil filter back. All in all it took about 4 hours to remove the remaining parts of the old exhaust and put the new exhaust in place before fitting the new oil filter.

and with the shiny new tail pipes looking and sounding great our work here was done part from filling her back up with oil and running her in.

Lovely

A lot easier with a lift

I am pleased to report that despite a small mishap with the oil filter the car is running well and sounds great and with everything copper eased should we need to do this again everything should come apart easier, all i have to do is a small trip to the tip to find the old exhaust a new home.

The old one out on the drive

The old one out on the drive

 

 

PLEASE NOTE – these are NOT instructions on how to undertake this job just some pics and words of our experiences, always consult professionals when undertaking any repairs or restorations. (please refer to the disclaimer on our about page)

Advertisements

Drive it Day 2014

So folks, Drive it Day…. the day in the spring we all wash, polish and proudly get out there in our beloved Classic Cars to show them off and have a jolly good day out to boot!!!

Heres the highlights from this year as posted on Facebook, Twitter and Instagram…..

Our first picture is from Frank McGregor – About to go for a spin in my 1977 Stag. Rego is a STAG and it lives in Hobart Tasmania!!

About to go for a spin in my 1977 Stag. Rego is STAG and it lives in Hobart Tasmania from Frank McGregor

Next up Suffolk and N.Essex Dirve It Day Highlights

Couple of nice pictures via Instagram

Carlo Maria Del Conte all the way from Italy

Carlo Maria Del Conte

Aberdeen Drive It Day.
From the Beach to the Royal Deeside Railway Centre for a coffee stop then on to Leith Hall. Over 80 cars took part from a 1912 Stanley Steam car to a new Focus. More pics from Aberdeen – Click Here

Aberdeen Drive It Day. From the Beach to the Royal Deeside Railway Centre for a coffee stop then on to Leith Hall. Over 80 cars took part from a 1912 Stanley Steam car to a new Focus.

More Stags enjoying days out

From Warwickshire area SOC a drive out through the lanes crossing into Leicestershire and a drive out in Haarlem in Holland

Nice montage from the Stilton Cheese run (is that a Stag warning a Stag???)

IMG_2208

And lastly, Classic Car Weekly promised to print EVER picture sent to them from Drive It Day – and here are the Stags that featured in the 10 pages they printed – well done guys a great memento to a great day…Till next year!